Super 20, is a single component, 20% acrylic high solids solvent compliant sealer made by SureCrete Design. It was developed for all SureCrete concrete systems and anywhere that cementitious surfaces require improvement to stain resistance, UV protection, and abrasion resistance. Super 20 will enhance the beauty of any multi-colored surface both vertically and horizontally. This product contains hybrid chemistry that provides vapor permeability yet is able to reduce the penetration of fluids in cement based surfaces. SureSeal provides superior penetration, adhesion, and protection. For use on all cement based surfaces, driveways, garage floors, patios, walkways, pool decks, stucco, and concrete block.

7039 HWY 276 Royce City, Texas 75189 Phone (972)289-1700 email: stevenv@decorativeconstructionsupply.com

SURFACE PREPARATION

Surface must be clean, free of dust, dirt, mildew, oil, grease, paint, sealers,
curing agents, waxes, and surface contamination.
Surface must be profiled, feeling like 120 grit sandpaper to the touch.
Utilize Super Concrete Renovator (SCR) to clean and profile concrete
surface. Evaluate dilution rate of water to SCR (usually between 2:1 and
4:1.) Coverage is approximately 150 sq. ft. per gallon. After spraying SCR
from SP pump-up sprayer, agitate with a nylon bristle broom. Allow to
stand until all foaming and bubbling has ceased. Do not allow SCR to dry on
slab, rinse frequently. For interior slabs wet vacuum rinsed areas. For exterior
slabs simply rinse away. Occasionally heavily soiled areas may require a
repeat application. Rinse thoroughly with water. Allow to dry thoroughly.
Surface must be cured, hydration complete.
Surface must be sound, no dusting, no spalling.

APPLICATION

Rolling
Utilize a bucket grid to apply in a thin film. Roller covers require a solvent
resistant core. The correct nap size varies due to texture. For example ¾”
may be required for heavy stamp overlay pattern, while mohair may be required
for smooth troweled finish. Do not allow puddling. Exercise care to
eliminate roller tracks through back rolling.
Spraying
Properly mask all areas requiring protection. Airless sprayer must be capable
of a minimum .5 gpm discharge. Tip size must be approximately .015” -
.017” with 65° fan. For horizontal surface utilize an 8” – 10” extension.
Maintain a wet edge between passes.
Apply when surface temperatures are between 50ºF and 90ºF and will stay within that range for 24 hrs. after
application. Do not apply outside if precipitation is forecast within a 24 hours of application.
Cure Time: Customarily first coat dries within 2 hours, if not sooner. Apply second coat when dry to the touch.
Allow 24 hrs. prior to foot traffic and 72 hrs. prior to vehicular traffic.
Coverage: Dependent upon porosity of substrate. Approximately 180 sq. ft. / gallon / coat.
Cleanup: Before SureSeal Super 20 dries; spills, over-spray, and tools can be cleaned up with any common
hydrocarbon solvent (e.g. Xylene).

MAINTENANCE

Pressure washing normally will remove dirt and grime. Tire marks can be removed with a mild detergent. Tire
marks made by heavy vehicles with very hot tires may discolor the coating. Such discoloration is generally not
removable. Hard braking or tire spin can result in permanent discoloration of the coating.

7039 HWY 276 Royce City, Texas 75189 Phone (972)289-1700 email: stevenv@decorativeconstructionsupply.com
We ship! Now shipping to: Texas, Louisiana, Mississippi, California, Oklahoma, Georgia, Florida, New Mexico, Arkansas, Arizona, Dallas, Nevada, Mesquite, Garland, Waco, Rockwall, Irving, Denton, Arlington, Allen, Mckinney, Richardson, Houston, Austin, Carrollton, Grapevine, Fort Worth, Lubbock, San Antonio, Frisco, El Paso, College Station, Galveston, 
San Marcus, Shreveport, New Orleans, Bossier City, Norman, Odessa... etc.